ICSE Class 10 Technical Drawing Applications Specimen Paper 2026-27

CISCE has published no specimen question paper for ICSE Technical Drawing Applications (65), either for ICSE 2027 or for ICSE 2026, so there is no official Technical Drawing Applications specimen paper to download. The official pattern comes from CISCE's ICSE 2027 Technical Drawing Applications syllabus: one written paper of three hours carrying 100 marks, with topics in Section A (topics 1 to 7) and Section B (topics 8 to 10), and Internal Assessment of 100 marks, marked 50 by the Subject Teacher (Internal Examiner) and 50 by an External Examiner. Every pattern line and mark on this page is copied from CISCE.
Is there an official ICSE Technical Drawing Applications specimen paper?
No. CISCE's circular PV/N/2026-2027 (9 October 2026) released ICSE 2027 specimen papers and marking schemes in 11 subjects, and Technical Drawing Applications is not one of them. For the other subjects the circular says "Please note that for the remaining subjects, the existing rubrics and assessment structure of Year 2026 Examination cycle shall apply." CISCE's ICSE 2026 specimen paper page has no Technical Drawing Applications paper either. So the only official word on the Technical Drawing Applications paper is the pattern printed in the ICSE 2027 Technical Drawing Applications syllabus, given below.
ICSE Class 10 Technical Drawing Applications specimen paper at a glance
Detail | Information |
Subject (code) | Technical Drawing Applications (65) |
Examination | ICSE 2027 |
Official CISCE specimen paper | Not published (2027 or 2026) |
Marking scheme available | No (no official paper) |
Paper | One written paper of three hours duration, 100 marks |
Theory sections | Section A: topics 1 to 7; Section B: topics 8 to 10 |
Internal Assessment | 100 marks |
Internal Assessment marking | Subject Teacher (Internal Examiner) 50 marks, External Examiner 50 marks |
Internal Assessment work | A file of minimum 15 drawing assignments, a three-dimensional model and a thermocol model |
Paper pattern and marks
There will be one written paper of three hours duration carrying 100 marks and Internal Assessment of 100 marks.
THEORY – 100 Marks
Section-wise pattern
CISCE prints the two sections and their topics, but no marks, number of questions or choices for each section.
Section | Topics |
SECTION A | 1. Geometrical Constructions based on Plane Geometry; 2. Area constructions; 3. Templates as an application of geometrical constructions and other constructions such as: 4. Scales; 5. Engineering Curves; 6. Solids; 7. Oblique drawing |
SECTION B | 8. Sections of right solids (prism, pyramid, cylinder and cone); 9. Isometric Drawing (Use of scale to draw isometric drawing may be included. e.g. 2:1 or 1:2 only). 10. Sectional Orthographic views (1st and 3rd angle methods) |
The full topic list, with every sub-point and scope line, is on our ICSE Class 10 Technical Drawing Applications Syllabus 2026-27 page.
ICSE Class 10 · 2026-27



Specimen papers, subject by subject
₹49a subject
Packs from ₹149
BUY 2, GET 1 FREE
See specimen papersInternal assessment marking
PART II- INTERNAL ASSESSMENT - 100 MARKS
To prepare a file containing minimum 15 drawing assignments. The drawing assignments should cover entire syllabus of class X. One / two assignments on each units of syllabus should be prepared on half imperial size drawing paper.
To make a three-dimensional model with stiff cartridge paper / chart paper involving the application of the development of solids such as a prism / pyramid.
To make a model with thermocol involving the application of the true shape of the section of truncated solids such as a prism / pyramid / cylinder / cone.
EVALUATION
The assignments/project work is to be evaluated by the subject teacher and by an External Examiner. The External Examiner may be a teacher nominated by the Head of the school, who could be from the faculty, but not teaching the subject in the section/class.
The Internal Examiner and the External Examiner will assess the assignments independently.
Award of Marks | (100 Marks) |
Subject Teacher (Internal Examiner) | 50 marks |
External Examiner | 50 marks |
How to use the official pattern
Learn the pattern first: one three-hour written paper of 100 marks covering all 10 topics in Section A and Section B, plus 100 marks of Internal Assessment, so give your drawing file and models as much time as the written paper.
Since CISCE has published no Technical Drawing Applications specimen paper, practise each topic from the syllabus page, including its scope lines (for example, in sections of right solids the figure shows the V.T. and H.T., and questions based on word problems are excluded).
Sit full timed practice in one go within three hours, with your drawing instruments, then check each drawing against the syllabus topic it comes from.
Do not leave the Internal Assessment to the end: build the file of at least 15 drawing assignments and the two models through the year.
Frequently asked questions
Has CISCE released an ICSE Class 10 Technical Drawing Applications specimen paper for 2026-27?
No. CISCE's circular PV/N/2026-2027 (9 October 2026) released ICSE 2027 specimen papers in 11 subjects, and Technical Drawing Applications is not among them. There is no Technical Drawing Applications paper on CISCE's ICSE 2026 specimen paper page either.
What is the paper pattern for ICSE Class 10 Technical Drawing Applications 2026-27 (ICSE 2027)?
One written paper of three hours duration carrying 100 marks, with Section A (topics 1 to 7) and Section B (topics 8 to 10), and Internal Assessment of 100 marks.
Does CISCE give marks for Section A and Section B?
No. The ICSE 2027 Technical Drawing Applications syllabus gives only the totals (100 marks for the theory paper, 100 for Internal Assessment). It prints no marks, question count or choices for either section.
How is the ICSE Class 10 Technical Drawing Applications internal assessment marked?
Out of 100: 50 marks from the Subject Teacher (Internal Examiner) and 50 marks from the External Examiner, who assess the assignments independently. The work is a file of minimum 15 drawing assignments, a three-dimensional model and a thermocol model.
Is there a marking scheme for ICSE Technical Drawing Applications?
No. CISCE has published no specimen paper for this subject, so there is no official marking scheme. The 2027 marking schemes cover only the 11 subjects named in circular PV/N/2026-2027.
More free ICSE Class 10 Technical Drawing Applications resources
ICSE Class 10 Technical Drawing Applications Syllabus 2026-27
ICSE Class 9 Technical Drawing Applications Syllabus 2026-27
Official CISCE source
Paper pattern and internal assessment marking: the official ICSE Technical Drawing Applications syllabus, Examination Year 2027 (PDF). Specimen papers: CISCE ICSE Class X specimen question papers 2027 and 2026 (no Technical Drawing Applications paper on either).
Checked on cisce.org on 16 November 2026. Syllabus text: CISCE.
Related free pages
- ICSE Class 10 Technical Drawing Applications Syllabus 2026-27
- ICSE Class 10 Syllabus 2026-27
- ICSE Class 10 Yoga Specimen Paper 2026-27
- ICSE Class 10 Specimen Papers 2026-27
- ICSE Class 10 Yoga Syllabus 2026-27
- ICSE Class 10 Robotics and Artificial Intelligence Specimen Paper 2026-27
- ICSE Class 10 Art Syllabus 2026-27
- ICSE Class 10 Physics Syllabus 2026-27


